Mesh Count to Micron Conversion Chart: Wire Mesh Opening Sizes

Choosing the right wire mesh starts with understanding its specifications. Mesh count, opening size, and wire diameter all affect a screen's performance, especially in filtration, screening, and separation applications.

A mesh count chart helps you estimate the opening size for a given mesh count. If your project requires a specific particle size, a wire mesh micron chart can help you narrow down your options before ordering.

However, mesh count and micron ratings are not always interchangeable. The actual opening depends on wire diameter and weave, so treat any mesh-to-micron conversion as a reference rather than a guarantee of filtration performance.

Use the chart below to compare common mesh counts with approximate opening sizes in inches and microns, and learn how to select the right specifications for your application.

 

Mesh Count to Micron Conversion Chart

The following wire mesh opening size chart provides approximate reference values for common square-weave wire mesh configurations. Typical uses are general examples, not guarantees of filtration performance.

Mesh Count (per inch)

Approximate Opening (inches)

Approximate Opening (microns)

Typical Use

4 mesh

0.187"

4,750 µm

Coarse screening and large-particle separation

10 mesh

0.075"

1,905 µm

Coarse sieving and debris screening

20 mesh

0.034"

864 µm

General screening and straining

30 mesh

0.021"

533 µm

Medium screening and particle separation

40 mesh

0.015"

381 µm

Fine screening and prefiltration

60 mesh

0.0092"

234 µm

Fine particle screening

80 mesh

0.007"

178 µm

Fine filtration and separation

100 mesh

0.0055"

140 µm

Fine screening and filtration

150 mesh

0.0041"

104 µm

Fine particle separation

200 mesh

0.0029"

74 µm

Fine filtration and screening

325 mesh

0.0017"

43 µm

Very fine filtration and particle separation


Important: These values are approximate and depend on the wire diameter and mesh construction used for each configuration. Different wire diameters can produce different openings at the same mesh count. For precise requirements, confirm the actual product specifications before ordering.

How to Convert Mesh Size to Microns

For square-weave mesh, you can approximate the opening size using the mesh count and wire diameter.

Opening size in inches:

Opening = (1 ÷ mesh count) − wire diameter in inches

Opening size in microns:

Opening in microns = opening in inches × 25,400

For example, a 20-mesh screen with a wire diameter of 0.016 inches has an approximate opening of 0.034 inches, or 864 microns.

These formulas apply to the clear opening of a conventional square weave. Other weave styles, including Dutch weaves, require additional consideration when determining the effective filtration opening.

 

What Is Mesh Count, and How Does It Affect Opening Size?

Mesh count refers to the number of openings per linear inch of wire mesh. A 20-mesh screen has 20 openings per inch in each direction when constructed as a square weave.

Generally, a higher mesh count means smaller openings, making the mesh suitable for separating finer particles. A lower mesh count typically provides larger openings for coarser screening and greater material flow.

However, mesh count alone does not tell you the exact opening size. Wire diameter takes up space bet

ween openings, so two screens with the same mesh count can have different clear openings.

When selecting wire mesh, consider the mesh count, wire diameter, opening size, and weave together.

 

Close-up of woven stainless steel wire mesh showing the weave pattern against a black background

 

Mesh Count vs. Gauge: What Is the Difference?

Mesh count and wire gauge describe two different measurements.

  • Mesh count indicates the number of openings per linear inch.

  • Wire gauge identifies wire thickness according to a particular gauge system.

  • Opening size measures the clear space between adjacent wires.

  • Micron size expresses an opening dimension in micrometers, where one micron equals one-millionth of a meter.

Never use wire gauge and mesh count interchangeably. A gauge number doesn't tell you how many openings appear in an inch, and mesh count doesn't indicate wire thickness.

For example, a 20-mesh screen with thicker wire will have smaller openings than a 20-mesh screen with thinner wire, assuming the same weave geometry.

Wire gauge conventions can also vary by material and sizing standard. Always confirm the actual wire diameter in inches or millimeters when precise dimensions matter.

For additional sizing information, visit TWP Inc.'s wire mesh gauge table.

 

Micronic Mesh Sizes and Filtration Applications

Micronic wire mesh is designed for applications requiring small, precisely specified openings. It is commonly used in industrial filtration, hydraulic systems, laboratory equipment, HVAC systems, and other applications where particle separation is important.

Unlike general-purpose mesh count references, micronic mesh specifications identify the actual opening size in microns. This is especially useful when an application requires a specific aperture rather than a general mesh designation.

TWP Inc. offers micronic wire mesh in a range of stainless steel grades and weave configurations. Depending on the product, options include fine openings for demanding filtration and separation applications.

For applications requiring multilayer construction, sintered stainless steel mesh is another option. Sintered mesh combines layers of metal mesh into a bonded structure and is used in applications such as hydraulic filtration, diffusers, and breather vents.

 

Does a Micron Rating Guarantee Filtration Performance?

No. A micron measurement describes an opening dimension or a specified filter rating, depending on the product. It does not automatically establish how efficiently a filter captures particles of that size.

Nominal and absolute micron ratings describe different filtration performance expectations. A nominal rating generally indicates partial particle removal, while an absolute rating indicates a defined efficiency under specified test conditions.

This distinction matters when selecting filters for applications that require consistent particle retention. Review the product specifications and relevant test data rather than relying on a micron number alone.

For additional background, read this guide to nominal versus absolute micron ratings.

 

How to Choose the Right Wire Mesh Opening Size

Before ordering wire mesh, consider your application requirements.

  • Determine the target particle size. Identify the particles you need to retain or allow through the mesh.

  • Confirm the opening size. Use the actual opening dimension in inches or microns when precision matters.

  • Consider wire diameter. Wire thickness affects the clear opening, strength, and available open area.

  • Identify the weave style. Plain weave, twill weave, Dutch weave, and sintered mesh have different construction characteristics.

  • Evaluate the operating environment. Temperature, chemicals, pressure, and flow requirements can influence material selection.

  • Verify the product specifications. Confirm the alloy, dimensions, and applicable filtration requirements before purchasing.

If you need help finding the right mesh, explore TWP Inc.'s services, request a quote, or contact the team for assistance with your specifications.